The Chopper Builders Handbook CD’s. The Chopper Builders Handbook CD’s. The Chopper Builders Handbook came about as much by accident as by. Posted on 01/05/ by Gary. As some of you might already know I’ve.
Author: | Kegal Shaktir |
Country: | Gambia |
Language: | English (Spanish) |
Genre: | Science |
Published (Last): | 7 July 2009 |
Pages: | 344 |
PDF File Size: | 9.24 Mb |
ePub File Size: | 9.16 Mb |
ISBN: | 405-5-68782-216-6 |
Downloads: | 9569 |
Price: | Free* [*Free Regsitration Required] |
Uploader: | Tutaxe |
Welcome To The Chopper Builders Handbook Online The primary objective of the Chopper Builders handbook is to provide basic information that will enable everyone to successfully build their own Chopper chopper builders handbook scratch. Nobody is going to give you a list of what is on the CD that isn’t on the site. Sep 23, 2018 The Chopper Builders Handbook came about as much by accident as by design. Nobody is going to give you a list of what is on the CD that isn’t on the chopper builders handbook. To make a long story short, I gave him a jpeg of the mounts dimensions and we posted it to xhopper discussion thread chopper builders handbook frame building.
In photos they appear awkward, out of proportion and unbalanced with respect to the size and placement of the ancillary components.
Dick Allen Blueprint Frames
As for worrying about it being locked down, I have downloaded every bit I could locate to a jump drive that I keep for these kind of things. We’ll do our original ‘Old School’ style and buillders ‘modernized’ version plus some repops of the old original Ness style forks from the sixties.
Yes, my password is: I guess that I felt it was the right thing to do since he made all this stuff available for free about 8 or 9 years ago. Link to where this site is?
Duane is a lifelong rider, fabricator and all around Biker par excellence who understands what builders need to keep their project moving forward. What we want to do initially is to create a set of rails that have a 27 inch piece of straight tube, a forty degree bend, another section of straight tube four inches long, and another forty degree bend ending up in a long straight section that runs to the end of the seven foot piece of tubing we started with for each side of the bike as seen in Figure 6.
We’re thinking about a Sportster tank at this stage but we haven’t decided whether to mount it low, high or in-between. Pages About The Handbook. Those guys are to busy doing other more productive work.
About The Handbook
One left and one right. Some of the vendors had some pretty big spaces and lots of stuff to sell.
Cyber-psychologists are already talking about this phenomena but I think that the relationship of men and machines is actually very old. This last statement brings us to the subject of learning how to find up, down and sideways on round tubing.
Most people think of the recip-saw as a carpenters tool. If you’re not using a jig the plates can be held tightly against the tubing by running some all-thread rod completely through both halves to hold them in place as you’re measuring and marking. Our original frame designs all used a simple piece of 1.
Once we have the notches cut and the two down tubes trial fit together nicely at the backbone we can finally measure the inward slope angles of these pieces and figure out how we need to place the lower rails in the bender to make the final bends where the tubing heads up towards the axle adjusters. Find More Posts by concrete guy. To build frames you also need a bender and welder or at least a friend who has access to those more expensive pieces of equipment.
In comparison the website only contains text pages and pictures so this CD has almost three times more information than we’ve covered online. One is a stock 81 that’s going to get the ‘mild’ treatment and one’s is based upon a fairly radical Paughco frame as seen below.
Do you already have an account? Remove Advertisements Sponsored Links. It’s in the shop for welding on the case which is busted at the base. Those should be the last two things you ever let go of. Others builders will often go a little further in an attempt to make a little prettier connection. Ninety percent of all mass produced frames we’ve worked on over the past couple of years have had the plates installed with a combination of these two common adjuster alignment problems which is why we want to point this problem out at the onset of this article.
The frame in Figure 6. It just so happened however that we did get a chance to talk with Mike Fass Mikey Vils and had a chance to reminisce about Dick Allen.
Most of the time none of these ‘trigger-points’ will never occur in the lives of the average person. In the same vein all of the vertical members should be plumb. As a last resort a regular old hanvbook will get the job done but will eat up a good chunk of time and give you some nasty blisters.
The complete set of CD’s contain over pages of fabrication instructions. Do you have the will and drive to see it through to the finish? Active Threads back again building again sayin hello Last Post: This gives you enough room to bring the axle all the way to the front to install a chain.
Visit the Main Site at: Originally Posted by kindyr. There is probably not much on the site that will benefiet you either at this point and time.